<meter id="nbrfp"></meter>

            <dfn id="nbrfp"><address id="nbrfp"><dfn id="nbrfp"></dfn></address></dfn>

                    <mark id="nbrfp"></mark>
                      Gear Oil Pumps | Hot Oil Pumps
                      Hot??
                      diesel oil transfer pump|Explosion-proof gear pump|Jacketed screw pump|KCB stainless steel gear pump

                      KCG high temperature resistant gear pump

                       
                      KCG high temperature resistant gear pump
                       
                      Summary
                      KCG type high temperature resistant gear pump Model: KCG Flow range: 1-58 cubic/hour Pressure: 0.1-2.5 MPA CAL: 20-100 - mm Structure: this series of high temperature gear pump structure and KCB gear pump structure is roughly the same, mai
                      Detail Introduction
                      KCG type high temperature resistant gear pump
                       
                       
                      Model: KCG
                      Flow range: 1-58 cubic/hour
                      Pressure: 0.1-2.5 MPA
                      CAL: 20-100 - mm
                       
                      Structure: this series of high temperature gear pump structure and KCB gear pump structure is roughly the same, mainly gear, shaft, pump body, safety valve, shaft seal (special requirements, can choose magnetic drive, zero leakage structure) and so on. The gear has higher hardness and strength after heat treatment (service life is much longer than the ordinary gear pump), the gear and the shaft are installed in the replaceable sleeve operation. All parts of the pump are lubricated through the transmission medium. The pump has a reasonable design of oil drainage and oil return groove, so that the gear in the work under the minimum torque force, so the bearing load is small, small wear, high pump efficiency.
                      The pump is provided with a safety valve as overload protection, the total backflow pressure of the safety valve is 1.5 times of the rated discharge pressure of the pump, but also can be adjusted in the allowable discharge pressure range according to the actual needs. However, it should be noted that the safety valve cannot be used as a pressure reducing valve for a long time. If necessary, it can be installed separately on the pipeline. Viewed from the overhanging end of the spindle to the pump, it rotates clockwise.
                       
                      Two: high temperature gear pump use: the pump is suitable for conveying no solid particles and fiber, temperature is not higher than 280≧, viscosity of 5×10-6 ~ 1.5×10-3 m2/s (5-1500CST) lubricating oil or other liquids similar to lubricating oil properties. If the conveying viscosity is higher, reduce the speed of the pump, the viscosity of the conveying medium can be 5×104cSt
                       
                      KCG type high temperature resistant gear pump performance parameters table

                       

                      笥 mm 送 楚 電竃坐mpa 簾 秘寔腎互業m       垢 恬 業oC C
                      L/min M3/h 孔 楕
                      KCG-1/0.6 ø25 16.5 1 0.6 5 300 1.5 Y90L-4
                      KCG-1.5/0.6 ø25 25 1.5 0.6 5 300 1.5 Y90L-4
                      KCG-2/0.6 ø25 33.3 2 0.6 5 300 2.2 Y100L1-4
                      KCG-3/0.6 ø25 55 3 0.6 5 300 2.2 Y100L1-4
                      KCG-5/0.6 ø40 83 5 0.6 5 300 3 Y100L2-4
                      KCG-6/0.6 ø40 100 6 0.6 5 300 3 Y100L2-4
                      KCG-7.5/0.6 ø50 125 7.5 0.6 5 300 4 Y132M1-6
                      KCG-10/0.6 ø50 165 10 0.6 5 300 5.5 Y132S-4
                      KCG-12/0.6 ø55 200 12 0.6 5 300 5.5 Y132M2-6
                      KCG-15/0.6 ø55 250 15 0.6 5 300 5.5 Y132S-4
                      KCG-18/0.6 ø55 300 18 0.6 5 300 5.5 Y132S-4
                      KCG-38/0.6 ø100 633 38 0.6 5 300 15 Y180L-6
                      KCG-38/1.0 ø100 633 38 1.0 3 300 22 Y200L-6
                      KCG-58/0.6 ø100 633 58 0.6 5 300 18.5 Y180L-4
                      KCG-58/1.0 ø100 633 58 1.0 3 300 30 Y200L-4

                       

                      Three: high temperature resistant gear pump selection and installation precautions: the correct selection is the key to obtain the best use effect, in order to meet the different physical and chemical characteristics and operation requirements of the medium, we suggest: the user put forward the pump operation data, by our company's professional selection recommended, and finally confirmed by the user. The following points should be noted when selecting the pump:
                      1, medium lubricity, cleanliness, corrosion.
                      2, the viscosity of the medium, temperature.
                      3, medium inlet and outlet pressure, installation height.
                      4, the use of explosion-proof requirements.
                      5, installation environment, horizontal or vertical, fixed or mobile, connecting pipeline special requirements.
                       
                      Four: KCG type high temperature resistant gear pump is made of special material, and must be bought to the regular manufacturer to avoid unnecessary losses in the process of use.
                      Related links
                      Related Products
                      Quick MenuGear Oil Pumps Hot Oil Pumps | RecommendationDiaphragm Pump AODD & EODD Copyright China pump manufacturer http://www.cqstbg.com Internet Content Provider:11002332-1
                      Address: Industrial Development Zone, Hebei Province Tel0317-8181816
                       
                      少妇被两个黑粗来回进出_大学生无套流白浆视频大全_久久亚洲国产_激情综合激情五月俺也去